iMP8 Series

1000–1200 Watt Configurable AC-DC Power Supplies

The iMP8 series is an AC input to DC output configurable power system consisting of a microprocessor-controlled PFC front end providing six slots that accept intelligent DC-DC converter modules with single, dual or triple outputs ranging from 2 V to 60 V. Single output modules come in four power ranges that can be mixed and matched and connected in parallel or series to obtain thousands of output combinations customized to any application. User-configurable functions include current limit and output sequencing, as well as input and output OK signals and indicators. Capable of delivering up to 1,200 watts and with up to 18 isolated outputs, the iMP8 series carries full medical safety approvals and is an extremely flexible and versatile multi-output power solution.

These digitally controlled power supplies feature a PMBus™-compliant I2C serial interface that enables parameters such as the voltage, current limit and enable/inhibit status of individual outputs to be programmed via an intuitive user GUI. The serial interface also allows remote monitoring of voltage, current and temperature.

iMP Software Package

Datasheet Press Releases Technical Documentation Print this page
  • Total Max Power:
    1,200 W
  • Total Max Current:
    240 A
  • Input Voltage:
    85 V to 264 V
  • Output Voltage:
    N/A
  • Outputs:
  • Size (L x W x H):
    10.000" x 7.000" x 2.500"
  • Warranty:
    2 years
  • Operating Temperature:
    -40°C to +70°C

Electrical Specifications

  • Input
  • Output
  • Logic Control
  • Isolation
  • Other
  • Input Range: 85-264 VAC; 120-350 VDC
  • Frequency: 47-440 Hz
  • Inrush Current: 40A Peak (Soft Start)
  • Efficiency: 85% typical depending on configuration
  • Power Factor: 0.99 typ @ full case load
  • Turn-on Time: AC 2,0 sec; Inhibit 150mS
  • EMI Filter: CISPR 22/EN55022 Level B
  • Leakage Current: 300uA Max
  • Radiated EMI: CISPR 22/EN55022 Level B
  • Holdover Storage: 20 mSec min
  • ACOK: >5mS early warning
  • Input Fuse: 20A
  • Margining: +/-4-6% of Nominal
  • Programming Accuracy: +/- 5%
  • Factory Set Point Accuracy: +/- 1%
  • Adjust Range: +/-10% Manual; Full Range Programmable
  • Overall Regulation: 0.4% or 20mV max
  • Ripple: RMS 0.1%; P-P 1.0% to 20MHz
  • Dynamic Response: <2% or 100mV, 25% load step
  • Reverse Voltage Protection: 100% of rated output
  • OVP: Programmable
  • OCP: Programmable
  • Recovery Time: To within 1% in <300uSec
  • Remote Sense: Compensates up to 0.5V
  • Thermal Protection: OTP/OTW Programmable
  • Single Wire Parallel: Share within 2% of total rated load
  • DCOK: +/-5% of nominal - Programmable
  • Output/Output Isolation: >1 Megohm, 500V
  • Safety: Meets EN60950 and EN60601
  • Module Switching Frequency: 250kHz accepts external sync signal
  • 5.0V/3.3V dual outputs
  • Enable (on/off)
  • Output loadsharing
  • Industry standard pin-out
  • Trim feature, both rails
  • 100°C Baseplate temperature
  • Unencapsulated 2.3" x 2.4" x 0.50" pkg.
  • 48VDC Input
  • Thermal protection

貴社の製品選択をお手伝いします

条件による新規検索

アーティセン・エンベデッドテクノロジーズ

Sales Support
☒ Close